{1} ok boot net Boot device: /pci@1f,700000/network@2 File and args: 100 Mbps FDX Link up >> NetBSD/sparc64 OpenFirmware Boot, Revision 1.14 100 Mbps FDX Link up Using BOOTP protocol: ip addr=10.1.1.2 hostname=usiii-bge0 netmask=255.255.255.0 gateway=10.1.1.1 root addr=10.1.1.1 path=/exports/usiii =0x856da8 Loading netbsd: 7973920+355688+547984 [541680+353946]=0x9b7b88 Loaded initial symtab at 0x18dc9f8, strtab at 0x19614e8, # entries 22544 consinit() stdin node = f0098cb8 stdout package = f0098cb8 buffer @ 0x1c05ca0 console is /pci@1e,600000/isa@7/serial@0,3f8 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 5.99.24 (SCHIZO) #0: Thu Jan 28 17:27:30 CET 2010 kiers@yvresse:/tmp/obj/sys/arch/sparc64/compile/SCHIZO total memory = 5120 MB avail memory = 5017 MB mainbus0 (root): SUNW,Sun-Fire-V210 (Sun Fire V210): hostid 83739a6f cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1002 MHz, UPA id 0 cpu0: 128K instruction (32 b/l), 256K data (32 b/l), 4096K external (64 b/l) cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1002 MHz, UPA id 1 cpu1: 128K instruction (32 b/l), 256K data (32 b/l), 4096K external (64 b/l) memory-controller at mainbus0 not configured memory-controller at mainbus0 not configured schizo0 at mainbus0: addr 4000ff00000: "Tomatillo", version 4, ign 7c0, bus B 0 to 0 schizo0: DVMA map: c0000000 to dfffffff IOTSB: 58e8000 to 5967fff pci0 at schizo0 bge0 at pci0 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet bge0: interrupting at ivec 37c8 bge0: pcistate failed to revert bge0: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:73:9a:6f brgphy0 at bge0 phy 1: BCM5704 1000BASE-T media interface, rev. 0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto Hardware Flags: - 5700 Family - Supports Jumbo Frames - No EEPROM bge1 at pci0 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet bge1: interrupting at ivec 37c9 bge1: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:73:9a:70 brgphy1 at bge1 phy 1: BCM5704 1000BASE-T media interface, rev. 0 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto Hardware Flags: - 5700 Family - Supports Jumbo Frames - No EEPROM schizo1 at mainbus0: addr 4000f600000: "Tomatillo", version 4, ign 780, bus A 0 to 0 schizo1: DVMA map: c0000000 to dfffffff IOTSB: 598c000 to 5a0bfff pci1 at schizo1 ebus0 at pci1 dev 7 function 0 ebus0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00 flashprom at ebus0 addr 0-fffff, 290-290 not configured rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819p i2c at ebus0 addr 320-321 ipl 46 not configured power at ebus0 addr 800-82f ipl 32 not configured com0 at ebus0 addr 3f8-3ff ipl 44: ns16550a, working fifo com0: console com1 at ebus0 addr 2e8-2ef ipl 44: ns16550a, working fifo rmc-comm at ebus0 addr 3e8-3ef ipl 44 not configured alipm0 at pci1 dev 6 function 0: 223KHz clock iic0 at alipm0: I2C bus ohci0 at pci1 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03) ohci0: interrupting at ivec 7a7 ohci0: OHCI version 1.0, legacy support usb0 at ohci0: USB revision 1.0 aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc4) aceride0: using ivec 1f98 for native-PCI interrupt atabus0 at aceride0 channel 0 atabus1 at aceride0 channel 1 schizo2 at mainbus0: addr 4000e600000: "Tomatillo", version 4, ign 700, bus A 0 to 0 schizo2: DVMA map: c0000000 to dfffffff IOTSB: 619a000 to 6219fff pci2 at schizo2 esiop0 at pci2 dev 2 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi) esiop0: using on-board RAM esiop0: interrupting at ivec 1f29 esiop0: alloc new tag DSA table at PHY addr 0xc0000000 scsibus0 at esiop0: 16 targets, 8 luns per target esiop1 at pci2 dev 2 function 1: Symbios Logic 53c1010-66 (ultra3-wide scsi) esiop1: using on-board RAM esiop1: interrupting at ivec 1f28 esiop1: alloc new tag DSA table at PHY addr 0xc0002000 scsibus1 at esiop1: 16 targets, 8 luns per target schizo3 at mainbus0: addr 4000ef00000: "Tomatillo", version 4, ign 740, bus B 0 to 0 schizo3: DVMA map: c0000000 to dfffffff IOTSB: 6280000 to 62fffff pci3 at schizo3 bge2 at pci3 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet bge2: interrupting at ivec 375c bge2: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:73:9a:71 brgphy2 at bge2 phy 1: BCM5704 1000BASE-T media interface, rev. 0 brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto Hardware Flags: - 5700 Family - Supports Jumbo Frames - No EEPROM bge3 at pci3 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet bge3: interrupting at ivec 375d bge3: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:73:9a:72 brgphy3 at bge3 phy 1: BCM5704 1000BASE-T media interface, rev. 0 brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto Hardware Flags: - 5700 Family - Supports Jumbo Frames - No EEPROM wm0 at pci3 dev 1 function 0: Intel i82545GM 1000BASE-T Ethernet, rev. 4 wm0: interrupting at ivec 744 wm0: Ethernet address 00:04:23:d8:d3:14 makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 5 makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto pcons at mainbus0 not configured No counter-timer -- using %tick at 1002MHz as system clock. Using %tick -- intr in 10020000 cycles Using %tick -- intr in 10020000 cycles scsibus0: waiting 2 seconds for devices to settle... scsibus1: waiting 2 seconds for devices to settle... atapibus0 at atabus0: 2 targets uhub0 at usb0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 cd0 at atapibus0 drive 1: cdrom removable esiop0: alloc newcdb at PHY addr 0xc0004000 sd0 at scsibus0 target 0 lun 0: disk fixed sd0: 70007 MB, 90774 cyl, 2 head, 789 sec, 512 bytes/sect x 143374744 sectors sd0: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing sd1 at scsibus0 target 1 lun 0: disk fixed sd1: 70007 MB, 90774 cyl, 2 head, 789 sec, 512 bytes/sect x 143374744 sectors sd1: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing esiop1: alloc newcdb at PHY addr 0xc0006000 Kernelized RAIDframe activated root on bge0 mountroot: trying smbfs... mountroot: trying nfs... nfs_boot: trying DHCP/BOOTP bge0: watchdog timeout -- resetting nfs_boot: timeout... bge0: watchdog timeout -- resetting nfs_boot: timeout... bge0: watchdog timeout -- resetting nfs_boot: timeout... bge0: watchdog timeout -- resetting nfs_boot: trying RARP (and RPC/bootparam) revarp failed, error=51 mountroot: trying msdos... mountroot: trying lfs... mountroot: trying ffs... mountroot: trying cd9660... Supported file systems: union umap tmpfs smbfs puffs ptyfs procfs overlay null nfs msdos mfs lfs kernfs ffs fdesc cd9660 no file system for bge0 cannot mount root, error = 79 root device (default bge0): bge0: watchdog timeout -- resetting wm0 dump device: file system (default generic): nfs root on wm0 nfs_boot: trying DHCP/BOOTP nfs_boot: DHCP next-server: 10.1.1.1 nfs_boot: my_name=usiii-wm0 nfs_boot: my_domain=test.net nfs_boot: my_addr=10.1.1.3 nfs_boot: my_mask=255.255.255.0 nfs_boot: gateway=10.1.1.1 root on 10.1.1.1:/exports/usiii root time: 0x4b61cf48 init path (default /sbin/init): init: copying out path `/sbin/init' 11 Thu Jan 28 17:30:31 UTC 2010 Not checking /: fs_passno = 0 in /etc/fstab Starting file system checks: Setting tty flags. Setting sysctl variables: ddb.onpanic: 2 -> 0 Starting network. Hostname: usiii IPv6 mode: host Configuring network interfaces: bge1. Adding interface aliases:. Building databases: dev, utmp, utmpx done Starting syslogd. Mounting all filesystems... Clearing temporary files. Checking quotas: done. Setting securelevel: kern.securelevel: 0 -> 1 Starting virecover. Checking for core dump... savecore - - - no core dump (no dumpdev) Starting local daemons:. ddb.onpanic: 0 -> 1 ddb.commandonenter: -> bt fsck -y /dev/sd0a ** /dev/rsd0a ** File system is clean; not checking fsck -y /dev/sd1a ** /dev/rsd1a ** File system is clean; not checking Updating motd. Starting sshd. Starting inetd. Starting cron. Thu Jan 28 17:30:52 UTC 2010 NetBSD/sparc64 (usiii) (console) login: root Password: Jan 28 17:31:01 usiii login: ROOT LOGIN (root) on tty console Last login: Thu Jan 28 17:26:16 2010 on console Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 The NetBSD Foundation, Inc. All rights reserved. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. NetBSD 5.99.24 (SCHIZO) #0: Thu Jan 28 17:27:30 CET 2010 Welcome to NetBSD! This system is running a development snapshot of the NetBSD operating system, also known as NetBSD-current. It is very possible that it has serious bugs, regressions, broken features or other problems. Please bear this in mind and use the system with care. You are encouraged to test this version as thoroughly as possible. Should you encounter any problem, please report it back to the development team using the send-pr(1) utility (requires a working MTA). If yours is not properly set up, use the web interface at: http://www.NetBSD.org/support/send-pr.html Thank you for helping us test and improve NetBSD. You have new mail. Terminal type is sun-ss5. We recommend that you create a non-root account and use su(1) for root access. usiii# exec bash bash-4.0# ident /netbsd |grep bge $NetBSD: if_bge.c,v 1.178 2010/01/28 07:34:12 msaitoh Exp $ bash-4.0#